$619.95
Save $-619.95
Tax includedShipping calculated at checkout
SKU: HB609E.572
Note: RS3 Vehicles will need to modify plug on wear sensor
Designed as an entry level endurance compound, there's nothing second-string about Hawk's Blue 9012 race compound. Easier to bed in and delivering excellent pad and rotor life, Blue 9012 is a medium torque pad developed specifically for Road, Rally and Circle Track racing.
Features:
All Hawk Performance compounds are not compatible with carbon ceramic rotors. Hawk pads are designed to work with Iron/Metal rotors.
Intermediate initial bite
Increased mid-mu characteristics
Medium
121Ã?C-538Ã?C operating temperature range
176Ã?C-426Ã?C optimal temperature range
Vehicle Fitment:
To ensure correct compatibility we always recommend comparing your existing brake pads to the pad shape diagram provided above. Vehicle fitment provided is to be used as a guide only and may not suit your vehicle.
Note: RS3 Vehicles will need to modify plug on wear sensor
2015-2019 Audi RS3 8V
2006-2008 Audi RS4 B7
2012-2018 Audi RS4 B8
2010-2016 Audi RS5 8T
2003-2005 Audi RS6 C5
2007-2015 Audi R8 42
Important - Installation and Brake Bedding Procedure:
STREET
Installation instructions should be followed in accordance with the application?specific brake pad installation instructions provided by the vehicle manufacturer.
Brake Pad Installation Procedure:
Install brake pads properly. Be sure pads are securely positioned in the caliper.
Check Brake Fluid. Flush and replace, as needed.
Check all hydraulic parts for excess wear and tear.
Check rotor for deep grooves or scoring. Resurface or replace rotor, as needed.
If rotors do not need resurfacing, then contamination from the previous brake pads must be removed. Sand rotors with 130?grit sandpaper using moderate pressure. Use soap and water to clean rotor surface after sanding. Rotors should be free and clear of oil, grease and brake fluid.
Inspect calipers for freedom of movement. Lubricate where necessary.
Street Brake Pad Burnishing/Bedding?In Instructions:
To break in the new components, make 6 to 10 stops from approximately 30 to 35 MPH
applying moderate pressure.
Make an additional 2 to 3 hard stops from approximately 40 to 45 MPH.
DO NOT DRAG BRAKES!
Allow 15 minutes for brake system to cool down.
Your brakes are now ready for use and can be driven normally.
MOTORSPORTS
Installation instructions should be followed in accordance with the application?specific brake pad
installation instructions provided by the vehicle manufacturer.
Brake Pad Installation Procedure :
Install brake pads properly. Be sure pads are securely positioned in the caliper.
Check Brake Fluid. Flush and replace, as needed.
Check all hydraulic parts for excess wear and tear.
Check rotor for deep grooves or scoring. Resurface or replace rotor, as needed.
If rotors do not need resurfacing, then contamination from the previous brake pads must be removed. Sand rotors with 130?grit sandpaper using moderate pressure. Use soap and water to clean rotor surface after sanding. Rotors should be free and clear of oil, grease and brake fluid.
Inspect calipers for freedom of movement. Lubricate where necessary.
Motorsports Brake Pad Burnishing/Bedding?In Instructions:
After reaching medium speed engage brake pedal to slow car without coming to a complete stop. Release pedal quickly and do not drag brakes. Repeat four or five times.
At higher speeds engage brake pedal to slow car without coming to a complete stop. Release pedal quickly and do not drag brakes. Repeat five times.
At or near race speed engage brake pedal to slow car without coming to a complete stop. Release pedal quickly and do not drag brakes. Repeat three times. Allow a few seconds between brake engagements while car is in motion.
Do not hold brake pedal. Park car for approximately 20 minutes or until brake rotors are completely cool to the touch.
If during the above steps the brake pedal becomes soft or brake fade is noticed, park the car immediately for approximately 20 minutes. Do not hold brake pedal.
IMPORTANT REMINDERS WHEN BURNISHING/BEDDING BRAKE PADS:
Do not attempt to use badly worn or damaged rotors with new brake pads.
Do not drag brakes while car is moving during break?in procedure.
Do not engage pedal while car is stopped at any time following the break?in procedure.
Upon completing the procedure, allow the brake system to completely cool before racing.
Applying the pedal a few times before the start of the race will allow the brake pads to heat up before attempting to reach race speeds.
Clean a used rotor surface with fine sand paper or steel wool, rinse with water, dry and install before bedding new pads.
Some forms of racing don’t allow time for the proper break?in procedure to be performed. However, it is still very important to attempt to perform at least the core of the procedure: Build up heat slowly and allow the system to completely cool down before racing if possible
